Zooz
HEAVY DUTY SWITCH
ZEN75 800LR
Binary Switch DT
HW: 03 FW: 03.10
EFR32ZG23A
7.19.2
0x027A (634)
0x7000 (28672)
0xA005 (40965)
ZC14-25030507
2025-03-12 10:36:16
N/A
Enhanced End Node 232
Always On End Node
Z-Wave Long Range On/Off Switch for fast and reliable control of your large lighting set-up and motors.
1 - Paddle Orientation
Choose if you want the upper paddle to turn the light on or turn the light off when tapped.Size: 1 byte
Default: 0
Minimum: 0
Maximum: 2
Possible values
| From | To | Desription |
|---|---|---|
| 0 | 0 | Up for on, down for off |
| 1 | 1 | Up for off, down for on |
| 2 | 2 | Up or down for on/off |
2 - LED Indicator
Choose if you want the LED indicator to turn on when the switch (light) is on or off, or if you want it to remain on or off at all times.Size: 1 byte
Default: 0
Minimum: 0
Maximum: 3
Possible values
| From | To | Desription |
|---|---|---|
| 0 | 0 | LED on when switch off |
| 1 | 1 | LED on when switch on |
| 2 | 2 | LED always off |
| 3 | 3 | LED always on |
3 - Auto Turn-Off Timer
Auto-off timer will automatically turn the switch off after x minutes once it has been turned on.Size: 4 bytes
Default: 0
Minimum: 0
Maximum: 65535
Possible values
| From | To | Desription |
|---|---|---|
| 0 | 0 | Timer disabled |
| 1 | 65535 | 1-65535 (minutes) |
5 - Auto Turn-On Timer
Auto-on timer will automatically turn the switch on after x minutes once it has been turned off.Size: 4 bytes
Default: 0
Minimum: 0
Maximum: 65535
Possible values
| From | To | Desription |
|---|---|---|
| 0 | 0 | Timer disabled |
| 1 | 65535 | 1-65535 (minutes) |
7 - Association Reports
Choose which physical and Z-Wave triggers should prompt the switch to send a status change report to the associated devices. See values for details.Size: 1 byte
Default: 15
Minimum: 0
Maximum: 15
Possible values
| From | To | Desription |
|---|
8 - On/Off Status After Power Failure
Set the on off status for the switch after power failure.Size: 1 byte
Default: 2
Minimum: 0
Maximum: 2
Possible values
| From | To | Desription |
|---|---|---|
| 0 | 0 | always off once restored |
| 1 | 1 | always on once restored |
| 2 | 2 | remembers and restores status |
9 - Scene Control
Enable or disable scene control functionality for quick double tap triggers.Size: 1 byte
Default: 0
Minimum: 0
Maximum: 1
Possible values
| From | To | Desription |
|---|---|---|
| 0 | 0 | scene control disabled |
| 1 | 1 | scene control enabled |
11 - Relay Control (Smart Bulb Mode)
Enable or disable physical and Z-Wave on/off control. Disable both for smart bulbs.Size: 1 byte
Default: 1
Minimum: 0
Maximum: 2
Possible values
| From | To | Desription |
|---|---|---|
| 0 | 0 | Disable paddle |
| 1 | 1 | Enable paddle and Z-Wave |
| 2 | 2 | Disable paddle and Z-Wave |
12 - 3-Way Switch Type
Choose the type of 3-way switch you want to use with this switch in a 3-way set-up.Size: 1 byte
Default: 0
Minimum: 0
Maximum: 1
Possible values
| From | To | Desription |
|---|---|---|
| 0 | 0 | Toggle on/off switch |
| 1 | 1 | Momentary switch (ZAC99) |
13 - Disabled Relay Behavior
Set reporting behavior for disabled physical control of the relay.Size: 1 byte
Default: 0
Minimum: 0
Maximum: 1
Possible values
| From | To | Desription |
|---|---|---|
| 0 | 0 | Reports status / changes LED |
| 1 | 1 | Doesn't report status / change LED |
14 - LED Indicator Color
Choose the color of the LED indicator. 0-white, 1 - blue, 2 - green, 3 - red.Size: 1 byte
Default: 1
Minimum: 0
Maximum: 3
Possible values
| From | To | Desription |
|---|---|---|
| 0 | 0 | white |
| 1 | 1 | blue |
| 2 | 2 | green |
| 3 | 3 | red |
15 - LED Indicator Brightness
Choose the LED indicator's brightness level. 0- bright (100%); 1-medium (60%); 2-low (30%).Size: 1 byte
Default: 1
Minimum: 0
Maximum: 2
Possible values
| From | To | Desription |
|---|---|---|
| 0 | 0 | bright (100%) |
| 1 | 1 | medium (60%) |
| 2 | 2 | low (30%) |
16 - Status Report Type
Choose how the switch reports its status back to the hub: binary switch for Z-Wave and basic set for physical (0) or binary switch for both (1).Size: 1 byte
Default: 1
Minimum: 0
Maximum: 1
Possible values
| From | To | Desription |
|---|---|---|
| 0 | 0 | Binary switch report for Z-Wave control, basic set report for paddle control |
| 1 | 1 | binary switch report for both Z-Wave and paddle control |
17 - Disable Paddle Programming
Enable (0) or disable (1) programming functionality on the switch paddles. For advanced users only, changes not recommended.Size: 1 byte
Default: 0
Minimum: 0
Maximum: 1
Possible values
| From | To | Desription |
|---|---|---|
| 0 | 0 | programming enabled |
| 1 | 1 | programming disabled |
18 - Scene Control From Remote 3-Way Switch
Enable scene control functionality from the momentary switch connected to ZEN75 in a 3-way installation.Size: 1 byte
Default: 0
Minimum: 0
Maximum: 1
Possible values
| From | To | Desription |
|---|---|---|
| 0 | 0 | scene control disabled commands from the remote 3-way switch disabled |
| 1 | 1 | scene control commands from the remote 3-way switch enabled |
19 - Disable LED Indicator Flash On Setting Change
Choose if the LED should flash whenever a parameter is adjusted on the device to confirm the change (0) or disable this feature (1).Size: 1 byte
Default: 0
Minimum: 0
Maximum: 1
Possible values
| From | To | Desription |
|---|---|---|
| 0 | 0 | LED indicator flashes to confirm a setting change |
| 1 | 1 | LED indicator doesn't flash if a setting is changed |
INCLUSION 1. Initiate inclusion (pairing) in the app (or web interface). 2. TAP UP 3 TIMES QUICKLY if using traditional Z-Wave inclusion. 3. The LED indicator will blink blue to signal communication and turn green for 3 seconds if inclusion is successful or turn red for 3 seconds if the pairing attempt fails.
EXCLUSION 1. Bring your Z-Wave gateway (hub) close to the switch if possible 2. Put the Z-Wave hub into exclusion mode (not sure how to do that? [email protected]) 3. Tap the lower paddle on the switch 3 times quickly (the LED indicator will start blinking blue) 4. Your hub will confirm exclusion, the LED indicator on the switch will turn green for 3 seconds, and the device will disappear from your controller''s device list reset
If your primary controller is missing or inoperable, you may need to reset the device to factory settings. To reset the switch, press and hold the lower paddle for 10 seconds until the LED indicator starts blinking. Release paddle, and immediately afer, tap the lower paddle 5 times to complete the reset. The LED indicator will flash blue 3 times and turn red for 3 seconds to confirm successful reset.
Smart Bulb Mode, Multi-Tap Central Scene Functionality
Enter the 5 digit DSK PIN if using SmartStart method + arrow pointing to the QR code and PIN on the switch
| Type | Value(s) |
|---|